HomeError CodesHow To Reset Error Codes On Bosch Dishwasher

How To Reset Error Codes On Bosch Dishwasher

If you own a Bosch dishwasher, you may have encountered error codes that prevent it from functioning properly. These codes can be frustrating and confusing, but fortunately, resetting them is not difficult. In this article, we will guide you through the steps to reset error codes on your Bosch dishwasher so that it runs smoothly again.

First, we will help you identify the specific error code by checking the display panel on your dishwasher. Then, we will show you how to troubleshoot common causes of these errors such as clogged filters or faulty valves. After that, we will walk you through turning off the power to your dishwasher and resetting its control panel to clear any lingering error messages. Finally, we’ll give tips for preventing future errors so that your Bosch dishwasher continues working efficiently for years to come.

Identifying the Error Code on Your Bosch Dishwasher

Now, let’s take a closer look at how your trusty dishwasher communicates with you through its flashing lights and beeps. When an error occurs, the dishwasher will display a code on its LED screen. Some of the most common codes include E01, E02, and E15. The first thing you need to do is identify which code your machine is showing.

To do this, refer to your Bosch dishwasher manual. It should have a page dedicated to explaining what each code means. If you don’t have access to your manual, you can also search online for the specific error code and find explanations from other users or appliance repair websites.

Once you’ve identified the error code on your Bosch dishwasher, it’s time to start troubleshooting. Depending on the nature of the problem, there may be some simple steps you can take to reset the machine and clear the error message without calling in a professional repair service.

Checking for Common Causes of Error Codes

As you investigate the issue, keep an eye out for any obvious culprits that may be triggering the problem. One common cause of error codes on Bosch dishwashers is a clogged or dirty filter. Check your owner’s manual to locate and remove the filter, then clean it thoroughly with soap and water before replacing it.

Another potential cause could be a malfunctioning float switch. This switch is responsible for detecting water levels in the dishwasher and telling the machine when to stop filling up. If this component isn’t working properly, your Bosch dishwasher may display an error code indicating that there’s too much or too little water in the appliance.

Lastly, pay attention to how you’re loading your dishes into the dishwasher. Incorrect placement can result in poor cleaning performance and trigger error codes. Make sure you’re not overloading the machine or blocking spray arms with large items like pots or pans. Remember to always refer back to your owner’s manual if you’re unsure about how to properly load your Bosch dishwasher.

Turning Off the Power to Your Dishwasher

To ensure your safety and avoid any potential electrical hazards, you’ll need to turn off the power to your dishwasher before proceeding with any troubleshooting steps. Start by locating the circuit breaker box in your home. Once you’ve found it, locate the switch that controls your dishwasher’s power supply. Flip this switch to the "off" position.

If you’re unsure which switch controls your dishwasher, consult your user manual or contact a professional technician for assistance. It’s essential to make sure that no electricity is flowing through your dishwasher before attempting any repairs or resetting error codes. You may also want to unplug the dishwasher from its power source as an extra precaution.

After turning off the power, wait a few minutes before restarting your dishwasher. This will give it time to reset itself and possibly clear any error codes that were present before. If the error code persists after turning the power back on, refer back to our previous subtopic on checking for common causes of error codes or contact a professional for further assistance. Remember always prioritize safety when dealing with electrical appliances!

Resetting the Control Panel

You can try fixing any issues with your dishwasher by restarting the control panel, which is done through a series of button presses and lights. First, locate the "Cancel" button on your dishwasher’s control panel. Press and hold this button down for at least 3 seconds until all the lights on the display turn off.

Next, release the "Cancel" button and press and hold the "Start/Reset" button instead. Hold it down for about 5 seconds or until you see the display light up again. This means that you have successfully reset your dishwasher’s control panel.

If resetting the control panel didn’t fix your issue, consult your Bosch dishwasher manual for further troubleshooting steps or contact customer support for assistance. Remember to always turn off power to your dishwasher before attempting any repairs or maintenance to ensure safety.

Running a Test Cycle

Let’s run a quick test to see if our dishwasher is working properly. This test cycle will help us identify any issues that may be causing the error codes to appear on our Bosch dishwasher. Here’s how you can run a test cycle:

  • Make sure the dishwasher is empty
  • Close the door and turn on the power
  • Press and hold the "Rinse" button for 5 seconds
  • Release the "Rinse" button and wait for 2 minutes
  • The test cycle should begin automatically

During the test cycle, pay attention to any unusual sounds or movements from your dishwasher. If everything appears normal, then your dishwasher may have simply experienced a temporary issue that has now been resolved. However, if you notice any persistent problem or error codes after running this test cycle, it may be best to seek professional assistance.

Running a test cycle is an easy way to determine whether your Bosch dishwasher is functioning correctly or not. It’s important to make sure that all aspects of your appliance are working as intended so that you don’t encounter further problems down the line. By following these simple steps, you can diagnose potential issues with ease and ensure that your dishwasher continues to operate smoothly in the future without any recurring error codes popping up again.

Checking for Leaks or Obstructions

Now, it’s time to check for any leaks or blockages that may be causing your dishwasher to malfunction. Start by examining the drain hose and making sure it is not kinked or clogged. If there are any obstructions in the hose, remove them carefully and make sure there are no sharp bends or twists. Next, inspect the dishwasher’s interior for any signs of leaks around the door gasket or spray arms.

To help diagnose potential problems with your Bosch dishwasher, refer to this table:

Problem Possible Cause
Dishwasher won’t start Control board failure
Dishwasher doesn’t fill with water Water inlet valve malfunction
Dishwasher makes strange noises during operation Clogged spray arm

If you do find a leak, turn off the power supply and water supply to your dishwasher immediately. Then, carefully examine all components of the machine in order to pinpoint where the leak is coming from. This could include everything from hoses and valves to pumps and motors. Once you’ve identified the source of the problem, replace or repair as necessary before resetting error codes on your Bosch dishwasher.

By checking for leaks and obstructions in your Bosch dishwasher’s system, you can often solve many common issues that cause error codes to appear. Remember to always exercise caution when working with electrical appliances, especially those involving water sources. With a little patience and attention to detail, you can quickly assess what may be wrong with your machine and get it running smoothly again in no time!

Cleaning the Filter and Spray Arms

Now that you’ve checked for leaks or obstructions, it’s time to move onto the next step: cleaning the filter and spray arms. This is an important part of resetting error codes on your Bosch dishwasher because blockages in these areas can cause issues with water flow and lead to error codes appearing.

To clean the filter, start by removing it from the dishwasher and rinsing it under hot water to remove any debris. Next, use a soft-bristled brush to gently scrub away any remaining particles. Once you’re satisfied that the filter is clean, replace it back into its slot in the dishwasher.

Next up are the spray arms. These are responsible for spraying water throughout the dishwasher during a wash cycle, so it’s important to make sure they’re clean and free of any blockages. To do this, remove each spray arm from its holder and rinse them under hot water. Use a toothbrush or similar tool to scrub away any buildup or debris on each arm before replacing them back into their holders.

By following these steps and keeping your filter and spray arms clean, you’ll be well on your way to resetting any error codes on your Bosch dishwasher. Remember to perform regular maintenance like this to keep your appliance running smoothly!

Inspecting the Water Inlet Valve

Take a look at the water inlet valve inspection section to ensure your dishwasher is receiving the proper amount of water for a squeaky-clean cycle. The water inlet valve is responsible for delivering water to your dishwasher, and if it becomes clogged or faulty, it can cause error codes to appear. To inspect the valve, first turn off power to your dishwasher and shut off the water supply. Then, locate the valve near where the water enters your appliance.

Symptoms Possible Causes Solutions
Error code E24 or E25 appears Clogged or faulty water inlet valve Inspect and clean or replace as needed
Dishwasher doesn’t fill with enough water for a full cycle Water inlet valve not opening fully or clogged Clean or replace the valve

Once you’ve located the valve, remove any debris or buildup that may be preventing it from functioning properly. You can use a toothbrush or small wire brush to gently scrub away any buildup on the screen filter. If this doesn’t solve the problem, you may need to replace the entire valve assembly.

By inspecting and cleaning or replacing your dishwasher’s water inlet valve as needed, you can help prevent error codes from appearing on your appliance. If you’re unsure about how to perform this task yourself, consider consulting with a professional technician who has experience working with Bosch dishwashers. With proper maintenance and care, you can keep your appliance running smoothly for years to come!

Contacting Bosch Customer Service

If you need assistance with your appliance and want to talk to a knowledgeable representative who can help answer any questions or concerns, contacting Bosch customer service is the best way to do so. They offer excellent customer support and are always ready to assist you in any way possible. You can reach them through email, phone call, or live chat on their website.

When contacting Bosch customer service, it’s important to have all the necessary information about your dishwasher at hand. This includes the model number, serial number, and purchase date. Having these details readily available will help their representatives identify your appliance faster and provide more accurate solutions.

Bosch also offers an online self-help center where you can find troubleshooting tips and guides on how to fix common dishwasher issues. If none of the solutions work for you or if you’re still unsure of what steps to take next, don’t hesitate to contact their customer service team for further assistance. They are committed to ensuring that every customer has a satisfactory experience with their products.

Preventing Future Error Codes

To ensure efficient and trouble-free operation of your Bosch dishwasher, it is important to take preventive measures. One way to prevent future error codes is to regularly clean the filters and spray arms. Accumulated debris can clog the filters and prevent water flow, leading to error codes. Additionally, check for any visible damage on the spray arms that may affect their ability to function properly.

Another preventive measure you can take is to use high-quality detergent specifically designed for dishwashers. Low-quality detergents or using too much detergent can cause sudsing, which may trigger an error code. It is also recommended to use rinse aid as it helps in drying dishes faster and prevents water spots from forming.

Lastly, make sure you load your dishwasher correctly by following the manufacturer’s instructions. Overloading your dishwasher or placing items in areas where they shouldn’t be may affect the circulation of water during a wash cycle, causing an error code. By implementing these simple preventive measures, you can minimize the risk of encountering future error codes on your Bosch dishwasher and enjoy its optimal performance for years to come!

Frequently Asked Questions

Can error codes on a Bosch dishwasher be reset without turning off the power?

To reset error codes on your Bosch dishwasher without turning off the power, simply press and hold the Start button for three seconds. This will reset the dishwasher’s control board and clear any error codes that may be present. However, it’s important to note that resetting the error codes does not fix the underlying issue causing them to appear in the first place. If you continue to experience problems with your dishwasher, it’s best to consult a professional technician who can diagnose and repair the issue for you.

How do you know if the error code on your Bosch dishwasher is a serious problem or just a minor issue?

When you see an error code on your Bosch dishwasher, it can be concerning. However, not all error codes indicate a serious problem. Some may simply require a minor adjustment or cleaning. To determine the severity of the issue, consult your dishwasher manual or search online for the specific code and its meaning. If it is a minor issue, such as a clogged filter or spray arm, you may be able to resolve it yourself by following the troubleshooting steps outlined in the manual. However, if the error code indicates a more serious malfunction, such as a faulty sensor or motor, it may be best to contact a professional technician for assistance.

Is there a way to prevent error codes from occurring on a Bosch dishwasher in the future?

To avoid error codes from occurring on your Bosch dishwasher in the future, there are a few things you can do. First, make sure to regularly clean and maintain your dishwasher as recommended by the manufacturer. This includes cleaning out the filters, checking for any clogs or obstructions in the spray arms, and ensuring that all parts are properly installed and functioning correctly. Additionally, try not to overload your dishwasher with too many dishes or use incorrect detergent amounts. Finally, if you notice any unusual noises or issues during a cycle, stop the cycle immediately and investigate the problem before continuing. By taking these steps, you can help prevent error codes from occurring and keep your Bosch dishwasher running smoothly for years to come.

What should you do if resetting the control panel doesn’t fix the error code on your Bosch dishwasher?

If resetting the control panel doesn’t fix the error code on your Bosch dishwasher, there are a few things you can try. First, make sure that the dishwasher is properly installed and level. If it’s not level, this could cause water to leak out and trigger an error code. You should also check the dishwasher’s filter and clean it if necessary. A clogged filter can prevent proper drainage and cause an error code to appear. Additionally, check your dishwasher’s hoses for any blockages or kinks that could be preventing water from flowing properly. If none of these solutions work, it may be time to call in a professional technician to diagnose and fix the issue with your Bosch dishwasher.

Are there any DIY solutions for fixing common causes of error codes on a Bosch dishwasher, such as clogged filters or spray arms?

To fix common causes of error codes on your Bosch dishwasher, there are several DIY solutions you can try. If your filters or spray arms are clogged, you can clean them by removing and washing them in warm, soapy water. You can also check the drain hose for any blockages and clear them out if necessary. Additionally, make sure that the dishwasher is properly leveled to ensure that it is draining correctly. By taking these steps, you may be able to resolve the issue without needing to reset any error codes on the control panel.


Congratulations! You have successfully reset the error codes on your Bosch dishwasher. By following these simple steps, you were able to identify the error code, check for common causes, turn off the power, reset the control panel, run a test cycle, clean the filter and spray arms, inspect the water inlet valve and contact customer service if needed.

To prevent future error codes from occurring, make sure to maintain your dishwasher regularly by cleaning it after every use and checking for any blockages or damage to parts. By doing so, you can ensure that your Bosch dishwasher will continue to work efficiently and effectively for years to come. Thank you for trusting us with your appliance needs!

Leave a Comment

Stella is the founder and chief editor of getdishwasher.com. For the last decade and a half, Her aim for this website was to help people make the right decisions for their dishwasher component upgrades.

Like it? Share it!